Search...
Menu

TL-Swap System For A1 Kit Assembly Manual

Download

Product Introduction

  • Product outline drawing

Accessory Package Contents and Parts list

①. List of Accessory Package Contents:

C2866.MP4_20261112_160444.709(1)

1.Installation video

  • You can watch the assembly video.

    说明书

Assembly steps

Step 1 Wire and test the circuit.

connect the switch, power wire, PCB,With the printer powered off, insert the 4-pin connector into the AMS port at the rear of the printer, paying attention to the orientation. After ensuring everything is correctly connected, turn on the printer. Press the microswitch, and the servo motor will rotate approximately 40-50 degrees. Release the switch, and the servo motor will return to its original position.

Step 2 Assemble the heated bed assembly

  1. Materials used:D2.5 L28mm Dowel pin,two M3x10 screws ,WD0.6 OD6mm Torsion spring

  2. The direction is shown in the figure:Use diagonal pliers to trim the torsion spring.

DSC08169DSC08173

Step 3 Install the

  1. Material used:four M3*6 (4 pieces) ,D6H3 Magnet

  2. The direction is shown in the figure:

C2877.MP4_20261113_095934.481(1)DSC08171DSC08176DSC08181

Step 4 Assemble the servo

FYSETC

  1. Material used: the servo,two M2*8 self-tapping screws

  2. The direction is shown in the figure:

DSC08180

Step 5 Assemble the smicroswitch

FYSETC

  1. Materials used: microswitch,two M2.5*16 screws,M2*8 self-tapping screw

  2. The direction is shown in the figure.:

DSC08192

Step 6 Assemble the PCB and the servo assembly

FYSETC

  1. Materials used:

  2. The direction is shown in the figure:

Step 7 Assemble the build plate magazine

  1. Materials used: four M3*6 and four M3*10 flathead screws,six 30*20*2 magnet,two M3*30

  2. he direction is shown in the figure: One set on each side (left and right), assembled and installed in the same way.

    DSC08195DSC08196DSC08198DSC08198DSC08199DSC08202DSC08203

Step 8 Assemble the left and right parts

FYSETC

  1. Materials used: D10H3 magnet,four M3*12 flat-head self-tapping screws,two M3*10 screws,8 M3*10 flat-head self-tapping screws

  2. The direction is shown in the figure:

    DSC08204DSC08205DSC08206

DSC08207DSC08208

DSC08209DSC08211

Step 9 Install the heated bed assembly

  1. Materials used:M3*20 and a large M3 washer,spring

  2. The direction is shown in the figure:

Step 10 Install the PCBA and the servo assembly onto the machine

  1. Materials used:two M3*22 self-tapping screws,M3*10 screw.

  2. The direction is shown in the figure:

Step 11 Assemble the build plate magazine onto the machine

  1. Materials used:four M3*10 self-tapping screws,four M3*10 hex screws,the sponge feet

  2. The direction is shown in the figure:

Step 12 Assemble the steel build plate.

  1. Materials used:two M3*6 self-tapping screws

  2. The direction is shown in the figure:

Step 8 Show the finished product

Step 9 Slicer settings

 

Tech Support

facebook group:Tech Support Email:hunter@fysetc.com

Forum:https://forum.fysetc.com/

3MFS:https://www.thingiverse.com/thing:7436896/files

Installation complete, enjoy using it !

Previous
PSF Feedback Sensor
Next
Displays
Last modified: 2026-11-19